FHXL-63 系列是 限流火警保护器(限流保护器),是一种具有过压、欠压、过流、漏电、温度和烟雾检测等多重保护功能的综合保护器。该产品具有模块化、智能化、可视化等优点。同时,它支持标准的 Modbus485 通信协议。 说明 :限流型火灾报警器 FHXL-63 使用手册

FHXL-63-0.jpg 放大

悬停

FHXL-63-6.jpg 放大

悬停

FHXL-63-4.jpg 放大

悬停

FHXL-63-3.jpg 放大

悬停

FHXL-63-2.jpg 放大

悬停

FHXL-63-0.jpg 放大

悬停

FHXL-63-1.jpg 放大

悬停

FHXL-63-0.jpg
FHXL-63-6.jpg
FHXL-63-4.jpg
FHXL-63-3.jpg
FHXL-63-2.jpg
FHXL-63-0.jpg
FHXL-63-1.jpg
全屏

限流火警保护器 FHXL-63

, , , , , ,

FHXL-63 系列是 限流火警保护器(限流保护器),是一种具有过压、欠压、过流、漏电、温度和烟雾检测等多重保护功能的综合保护器。该产品具有模块化、智能化、可视化等优点。同时,它支持标准的 Modbus485 通信协议。
说明 :限流型火灾报警器 FHXL-63 使用手册

 导言


限流火警保护器
限流火警保护器

FHXL-63 系列是 限流火警保护器限流保护器)它是一种综合保护器,具有过压、欠压、过流、漏电、温度和烟雾检测等多种保护功能。该产品具有模块化、智能化、可视化等优点。同时,它还支持标准的 Modbus485 通信。

协议。所有保护参数,如过电压、欠电压和过电流保护,均可根据功率需求进行设置,以确保保护器能在发生下列情况时立即切断电源 过电压当线路出现欠压、过流等故障时,可以保护电气设备免受损坏。

产品结构紧凑,外形美观,安装时有标准导轨。

Current protection parameters


类型 JGXL-63/3P+N
当前规格 63A(1~63A)
过电压设置范围 交流 270 伏(210~300 伏)
欠压设置范围 交流 170 伏(80~200 伏)
工作电压 AC230V/400V

Product functional features


■ Smoke and combustible gas protection function: When the smoke, liquefied petroleum gas, natural gas, propane, butane and other combustible gases in the electric field exceed the limit, the protector will emit an audible and visual alarm signal, automatically cut off the power supply, and display real-time fault records.
Short circuit protection function: The protector monitors the current of the power line in real time. When a short circuit fault occurs in the line, it can achieve fast current limiting protection within 0.1 seconds and display real-time fault records.

■ Overload protection function: When the current of the protected circuit is overloaded and the overload duration exceeds the action time (3-60 seconds can be set), the protector starts current limiting protection and displays real-time fault records.
Overvoltage protection function: When the protector detects under voltage or over-voltage in the line, it automatically cuts off the power supply and displays real-time fault records.

■ Distribution cable temperature monitoring function: When the temperature of the monitored cable exceeds the alarm set value, the protector automatically cuts off the power supply and displays real-time fault records.

■ Leakage current monitoring function: When the leakage of the monitored line exceeds the alarm set value, the protector automatically protects and cuts off the power supply, and displays the fault record in real time.

■ Communication networking function: The protector has one RS485 interface, which can send data to the background monitoring system, realizing the five remote functions of remote telemetry, remote signaling, remote control, remote adjustment, and remote viewing.

■ Simultaneous cutting of neutral and live wires: When a fault occurs in the circuit, the product cuts off both the neutral and live wires simultaneously, without the danger of live wires on the circuit due to the failure of the neutral wire to be cut off.

Overvoltage does not damage: When the three-phase power supply is misconnected, the maximum power supply voltage is at AC450V, and the product will disconnect within the set time, while the ground product itself will not be damaged due to high voltage.
Anti harmonic: Currently, the electricity consumption in the power grid is relatively complex, with a large number of harmonics present. Harmonic hazards can shorten the lifespan of other electrical equipment, but this product is not affected in harmonic power grids.
One click recovery function: When users are not proficient in product operation and cannot meet on-site protection requirements for parameter settings, they can easily restore the factory settings to avoid erroneous protection issues caused by improper operation.

工作条件


1.首次正常通电时,设备延时 1 秒后自动断开;首次通电时,在过压、欠压、过流和漏电条件下,设备将在 3 秒内自动断开;

2.首次通电时,烟雾传感器需要加热 60 秒,然后产品进入保护状态。发生烟雾报警并排除故障后,需要手动按下复位键 2 秒钟,烟雾报警才能解除。

3.电流保护参数:

a. ≥ 1.05 倍电流,< 3 分钟开启。

b. ≥ 1.2 倍电流,设置范围 1 至 120 秒,默认为 10 秒

c. 电流≥ 2 倍,开度≤ 0.2 秒。

4.环境温度不得超过 +40°C,不得低于-5°C;24 小时内的平均温度不得超过 +35°C;在 +40°C,环境空气湿度不得超过 50%。

5.安装地点的海拔高度不得超过 2000 米。

6.污染程度:III.

7.安装环境中不得有爆炸性危险介质,不得有腐蚀性、破坏性气体和导电粉尘,不得有雨雪侵袭。

限流火警保护器是关键的功能之一


1.设置键:按住设置键 2 秒钟,进入设置状态。进入设置状态后,每按一次该键,系统将进入下一个设置菜单;

2.移位键:查询产品当前的实时运行参数。在设置状态下,具有位移功能;

3.数据键:查询产品上次故障信息,更改设置状态下的待设置参数;

4.复位键:当发生第一次过流或漏电时,产品会在延迟指定的复位时间后自动开启。当发生第二次过流、漏电或火警时,必须确认电路无故障,然后手动按下复位键使产品接通,并按下复位键 2 秒钟保存并退出设置状态。

标准套餐信息


纸箱尺寸(厘米) 包装清单 数量 毛重(千克)
45.5 厘米 × 23.5 厘米 × 31.5 厘米  守护者 60 件 20 公斤

限流火警保护器 尺寸


 

fireproof-current-limiting-protector

 


现在就联系我们,提供免费样品

如需了解有关我们产品和服务的更多信息,您将收到电气专家的回复,我们期待为您提供帮助。

Mob/WhatsApp/Wang:+86 18958900126
电子邮件:sales@tokeep.net
 电子邮件:tokeepcc@gmail.com

滚动至顶部